Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Roseville?
Gate repair in Roseville, CA typically costs $175 to $650 for common fixes like hinges, latches, rollers, and track adjustments, while electric gate repair involving motors, control boards, or wiring usually runs $300 to $1,200. Full automation retrofits and operator replacements sit at the higher end, from $900 to $2,500 installed. Every price we quote is set per job by a free written estimate, so you know the number before anyone touches your gate.
We’re a gate specialist, not a generalist. That matters for pricing because the technician who shows up already knows the brand on your post – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, or Mighty Mule – and diagnoses by that system’s logic instead of guessing and swapping parts. Our technicians have up to 15 years of experience, and the work is licensed, insured, and priced upfront. Call (855) 431-0356 to book your free on-site estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- Manual gate repairs in Roseville commonly land between $175 and $650.
- Electric and automated gate repairs typically run $300 to $1,200 depending on the failed component.
- Operator replacement with a new automated system usually falls between $900 and $2,500 installed.
- Estimates are free, and the written estimate sets the final price – not a phone quote.
- Brand-specific diagnostics prevent the most expensive mistake we see: replacing a $150 part when a $15 one failed.
Gate Repair Cost Breakdown (2026)
Here’s what the main repair categories run in the Roseville market. These are typical ranges, not a menu – your written estimate is the binding number.
| Repair Category | Typical Cost Range | What’s Usually Involved |
|---|---|---|
| Hinge, latch, and hardware repair | $175 – $400 | Replace worn hinges, align the gate leaf, adjust or replace latches |
| Gate sagging and post adjustment | $200 – $550 | Reset the leaf, tighten or re-anchor hinges, address settled posts |
| Roller and track repair (slide gates) | $200 – $600 | Replace rollers, realign track, correct the gate riding off the track |
| Electric operator diagnosis and repair | $300 – $800 | Motor testing, receiver and remote issues, limit switch adjustment |
| Control board replacement | $400 – $900 | Failed circuit board, water intrusion damage, board-level diagnosis |
| Wiring and power supply repair | $350 – $1,000 | Damaged low-voltage runs, transformer and power issues, connections |
| Complete operator replacement (installed) | $900 – $2,500 | New automatic operator, mounting, setup, and testing |
| New gate installation | $2,500 – $9,000+ | Varies widely by gate size, material, automation, and site conditions |
What pushes a repair toward the top of a range: a failed control board rather than a sensor, wiring that has to be located and replaced rather than re-terminated, and heavy or oversized leaves that need more labor to move and align. What pulls it down: a straightforward hinge or roller swap, a receiver that needs re-pairing rather than replacing, and a gate that’s sagging only because two hinges loosened. Electric gate work sits in its own tier because control boards, receivers, and motor assemblies are our routine work, not an escalated job – we’re not sending a generalist who’ll call someone else halfway through.
What Affects Gate Repair Pricing in Roseville
- Manual vs. electric system. A manual swing gate with a broken hinge is a short job. The same gate with a failed operator and a dead control board is a half-day diagnostic. Electric and automated systems are a core specialty for us, and the price reflects real component work, not a blanket call-out.
- The brand on your post. We work with LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Each brand has its own failure patterns and its own parts path. A tech who knows that a specific series’ board fails at the power input terminal saves you the cost of guessing.
- Gate type and weight. Sliding gates and heavy double-swing leaves take more labor to lift, align, and test than a single lightweight pedestrian gate. Heavy panels also raise the safety stakes, which means longer, more careful work with the gate locked off and power cut.
- Access to the operator and wiring. A control box mounted in the open and easy to reach prices differently from one tucked behind landscaping or buried conduit runs that have to be traced. We’ll flag access issues at the estimate, not mid-job.
- Post condition. A gate that’s dragging often has a settled post underneath it, not a bad hinge. Correcting the footing adds cost but fixes the actual problem. Roseville’s dry summers and wet winters move soil in ways that affect post stability over time, especially on gates set in unirrigated soil.
- Whether a permit is needed. New gate installations and some electrical work may require permits. Most cities require a permit for structural and electrical work like this, so ask the City of Roseville building department what applies to your project. We’ll tell you what to ask.
One local factor worth naming: Roseville’s inland valley heat is hard on outdoor electronics. Control boards, receivers, and operator housings sit in full sun through triple-digit summers, and heat is a common contributor to board and receiver failures. It’s one reason we test components in place before recommending replacement – a board that cooked in July may need a shade solution as much as a new board.
Electric Gate Repair: What Drives the Number
Electric gate repair in Roseville usually costs $300 to $1,200, and the range is wide because “the gate stopped working” has about a dozen causes. A gate that won’t open could mean a failed receiver, a dead remote battery, a tripped safety sensor, a misadjusted limit switch, a blown transformer, or a failed control board. Each one prices differently.
This is where brand fluency pays for itself. A DoorKing system with an access-control loop issue behaves nothing like a Mighty Mule with a solar-charged battery problem. We diagnose by the brand’s actual logic, which shortens the job and stops the parts-cannon approach. If you want a sense of how we handle the broader repair category, see our gate repair page.
A safety note that matters here: the wiring and power side of a gate operator is genuinely dangerous work. Low-voltage control wiring is one thing, but line voltage at the transformer or a solar-battery setup under load can seriously injure someone who doesn’t know what they’re touching. Don’t open the control box, and don’t probe the power side yourself. That’s a trained professional’s job, and it’s part of what you’re paying for.
How to Save on Gate Repair
Most savings come from booking the right work at the right time, not from finding a cheaper hourly rate.
- Get the free estimate before anything is ordered. We diagnose on-site and quote in writing. That prevents a part being ordered and installed on a guess. Call (855) 431-0356 to set it up.
- Fix the small stuff early. A single loose hinge gets cheap attention now. Left alone it thins the gate’s alignment and eventually sags the whole leaf – turning a hardware job into a post job.
- Repair before you replace where the diagnosis supports it. We’re brand-agnostic and work with whatever system you already have. If a control board is the only failure, we say so. If the motor is done, we say that too – but you’ll hear it after a test, not a sales pitch.
- Group the work. If your gate needs hinges and an operator service, doing both in one visit saves a second trip. Mention both when you book the estimate.
- Ask about shade and drainage for outdoor electronics. A simple change in how the operator housing is positioned or shielded can extend component life in Roseville’s heat. It’s the cheapest money you’ll spend on gate repair.
New Gate Installation: What It Costs and Why
New gate installation in Roseville generally starts around $2,500 and rises to $9,000 or more depending on size, material, automation, and site conditions. A single pedestrian swing gate is a smaller job than a double driveway gate with automation and access control. A full driveway gate with a new operator, posts, and wiring sits at the upper end.
Installation pricing has more moving parts than repair pricing because more of it is site-dependent: footing depth and how far the gate travels, the condition of the existing drive or approach, whether power is already at the post, and the exact operator you select. Any quote given before we’ve seen the site is a guess. We price installation from an on-site estimate, the same free one we use for repairs.
For installation we work across the same nine brands – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule – and we don’t push one brand because it’s easy for us. The right system is the one that fits your gate, your traffic, and your access needs. For a broader look at our full range of work, start at Gate Repair Roseville.
Manual Gate Repair vs. Electric: Quick Price Comparison
If you’re trying to decide which side of the cost table you’re on, here’s the short version. Manual gate repairs in Roseville usually run $175 to $650. Electric gate repairs usually run $300 to $1,200. A manual repair is hardware and alignment. An electric repair is hardware plus electronics, and the electronics are where the parts cost sits. Adding automation to a manual gate is a separate line item – plan on $900 to $2,500 installed for the operator alone, plus any gate modifications the site needs.
If an electric gate has stopped working reliably, the worst move is running it manually for months on a fault that’s getting worse. A gate that trips its limit switch today may grind a motor tomorrow. Booking the diagnostic early keeps the repair on the low side of the table.
FAQs – Gate Repair Cost
How much does gate repair cost in Roseville?
Gate repair in Roseville typically costs $175 to $650 for common hardware and alignment fixes, and $300 to $1,200 for electric gate repairs. The final number is set by your free written estimate. Call (855) 431-0356 for an exact quote – estimates are free.
Is it cheaper to repair my gate or replace it?
Repair usually wins on a gate under 15 years old with sound posts and frame; replacement makes more sense when the frame is bent, the posts are failing, or several components have failed at once. We diagnose first and quote repair against replacement, then you decide. Call (855) 431-0356 to book the estimate.
How much does a control board replacement cost in Roseville?
Control board replacement typically runs $400 to $900 installed, depending on the brand and board. We test the board in place before recommending one, because heat-damaged receivers and dead batteries mimic board failure. Call (855) 431-0356 for a brand-specific quote.
Can you fix my electric gate the same day?
Same-day repair is often possible when you call early, and we answer 24/7 with fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. Call (855) 431-0356 and we’ll tell you the soonest we can get there.
Do you work on my brand of gate operator?
Yes – we work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We’re independent and experienced with each brand, and we work with the system you already have. Call (855) 431-0356 with your model and we’ll confirm.
Is the estimate really free?
Yes. The on-site estimate is free, and the price is set per job by the written estimate. No service-call fee, no diagnostic fee, and no surprise line items. Call (855) 431-0356 to schedule yours.
Whether your gate is a manual swing that won’t latch or a fully automated slide gate with a dead operator, the fastest way to a real number is an on-site estimate. Call (855) 431-0356. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. We’re a dedicated gate specialist, so the person at your gate knows the system, the brand, and the fix – from control board to concrete post.
Pricing reflects the Roseville market as of 2026. Gate Repair Roseville offers free estimates – call (855) 431-0356.
Written by the team at Gate Repair Roseville.
What Our Customers Say
"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Javier Martinez"Hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a whole new gate, which two other companies had pushed for."
- Claudia Reyes"Solar panel on our remote gate wasn't keeping the battery up through the winter. He repositioned it, replaced the battery, and explained the math on why the old placement was never going to work."
- Kevin Sutton