Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Roseville?
Gate installation in Roseville typically costs between $2,400 and $9,500, with a standard residential driveway gate landing around $4,200 to $6,800 installed. A basic manual swing gate on existing posts runs $2,400 to $3,600, while a fully automated dual-swing driveway system with a LiftMaster or DoorKing operator commonly falls between $7,000 and $9,500. The written estimate you receive after we look at the site is what sets your final price.
We’re a gate specialist, not a generalist. Every tool and every technician skill we invest in is built around gate systems, which means we’re diagnosing swing gates, slide gates and their operators by brand-specific logic rather than guesswork. Whether you need a manual gate hung or an electric driveway system wired and programmed, the conversation starts with what your property actually needs.
Key Takeaways
- Typical installed cost for a Roseville residential driveway gate: $2,400 to $9,500, depending on material, span and automation.
- Automation adds roughly $1,500 to $3,500 to a manual gate installation on its own.
- We work on equipment from LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule.
- Our technicians have up to 15 years of experience.
- Estimates are free, and pricing is set per job by the written estimate.
Gate Installation Cost Breakdown (2026)
These are typical Roseville-market estimates for 2026. Real numbers move with material, gate width, site conditions and operator choice, and the written estimate is always the figure that counts.
| Line Item | Typical Cost Range |
|---|---|
| Manual swing gate (single leaf, up to 12 ft), installed on existing posts | $2,400 – $3,600 |
| Manual swing gate, new posts and footings included | $3,400 – $5,200 |
| Dual-swing driveway gate, manual | $4,200 – $6,800 |
| Sliding gate (up to 16 ft), manual | $3,800 – $5,800 |
| Swing gate operator, single leaf, installed and programmed | $1,500 – $2,800 |
| Slide gate operator, installed and programmed | $2,000 – $3,500 |
| Dual-gate operator setup with safety sensors and keypad | $2,800 – $4,500 |
| New concrete footings (per post) | $250 – $600 |
| Low-voltage wiring run (per foot, typical driveway distance) | $8 – $18 |
| Gate removal and haul-away of the old unit | $150 – $400 |
| Fully automated dual-swing system, turnkey | $7,000 – $9,500 |
What pushes a price up most often is automation paired with site work: new footings, a long low-voltage wiring run, and the labor to align and program the system so it cycles cleanly. What keeps a price down is a property where posts are already sound, the gate opening is a standard width, and the homeowner chooses a manual gate with no operator at all. Material choice matters too. An ornamental steel gate costs more than a wood or aluminum frame unit of the same span.
What Affects Gate Installation Pricing in Roseville
- Gate type and span. A single-leaf swing gate is the simplest install; a dual-swing driveway system doubles the hardware, footings and alignment work. Slide gates need a clear travel path and a level track, which adds site prep on sloped lots.
- Automation and brand. Adding an operator is the single largest line item, and brand choice shifts the number. We’re familiar with LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule, so we’re not steering you toward one proprietary system for convenience. We match the operator to the gate and the property.
- Site conditions. Roseville properties in neighborhoods like West Roseville and Fiddyment Ranch often sit on lots where the driveway approach needs grading before a slide gate will track right. New footings, trenching for wiring, and clearing old concrete all add cost.
- Material. Wood, aluminum, ornamental steel and chain-link frames sit at different price points for the same opening width. A taller or wider custom gate costs more in both material and hardware.
- Electrical access. An automated gate needs low-voltage wiring run from a power source to the operator, plus safety sensors. The longer and more complex that run, the higher the labor.
- Permits. Many cities require a permit for gates and for the electrical work tied to an operator. Ask the City of Roseville building department what your project needs before work starts, since permit fees and inspection timing affect the total.
How to Save on Gate Installation
The biggest cost lever is deciding early whether you need automation. A manual gate installed now, with the posts and footings sized for a future operator, lets you split the project: get the gate hung and usable, add the operator later when it fits your budget. That’s not cutting a corner. It’s sequencing the work so the structure is ready for what comes next.
A few other practical ways to keep the number down:
- Choose a standard opening width where the site allows it. Custom spans drive up both material and hardware cost.
- If your existing posts are sound and properly set, keeping them saves the footing and removal line items entirely.
- Consolidate the low-voltage wiring run into one clean path to the operator location. Rerouting later means paying for labor twice.
- Talk through the operator brands up front. We’ll walk you through the trade-offs between a Ghost Controls, Mighty Mule, LiftMaster or FAAC unit for your gate size, so you’re paying for the operator that fits, not the one that’s easiest to sell.
- Get a free on-site estimate before any work starts. Call (855) 431-0356 and we’ll set a time to look at the property. The estimate costs nothing, and it’s the figure that sets final pricing.
Manual vs. Electric Gate Installation: What’s the Cost Difference?
Electric automation adds roughly $1,500 to $4,500 over an equivalent manual gate, depending on whether you’re automating a single leaf or a dual-swing driveway. A manual swing gate that runs $2,400 to $3,600 installed becomes a fully automated single-leaf system in the $4,500 to $6,500 range once an operator, sensors, wiring and a keypad are added. A dual-swing driveway system moves from $4,200 to $6,800 manual up to $7,000 to $9,500 fully automated.
Electric work is a core part of what we do, not a side offering. Wiring, control boards, receivers and motor assemblies are routine for us. That matters for installation because a gate and its operator have to be commissioned together. A gate that’s hung well but paired with an operator that’s never been programmed against its weight and travel will bind, strain and fail. We install the gate, set the operator and walk the system through a full cycle before we leave. From control board to concrete post, it’s the same trade.
What’s Included in a Gate Installation Estimate?
A written gate installation estimate from us covers the gate unit or frame, the hardware, the operator if there is one, footings where new ones are needed, wiring where it applies, removal of the old gate, and the labor to set and align everything. It also lists what isn’t included, so there’s no surprise line item later. On an automated system, that includes the safety reversal sensors and any access controls such as a keypad or entry device.
Every installation uses whatever existing or new system fits the property. We don’t push a brand for our own convenience. If you already have a LiftMaster operator on one side of the property and want a matching gate on the other, we’ll work with that system. If you’re starting fresh and want to know what an entry-level Mighty Mule unit will handle versus a commercial-grade DoorKing setup, we’ll lay out the differences in plain terms. The right fix for your existing system is the goal, and that starts with the estimate.
Frequently Asked Questions About Gate Installation Cost in Roseville
How much does a basic manual gate installation cost in Roseville?
A basic manual swing gate in Roseville typically costs $2,400 to $3,600 installed on existing posts, climbing to $3,400 to $5,200 when new footings are needed. Call (855) 431-0356 for a free on-site estimate and an exact figure.
How much does it cost to add an electric gate operator?
Adding a single-leaf swing operator, installed and programmed, typically runs $1,500 to $2,800. A slide gate operator with wiring and safety sensors falls between $2,000 and $3,500. Call (855) 431-0356 and we can quote the operator that fits your gate.
Can I install a manual gate now and automate it later?
Yes. If the posts and footings are sized for a future operator, you can install the gate manually now for $2,400 to $3,600 and add automation later for $1,500 to $2,800, spreading the cost across two projects. Call (855) 431-0356 to plan the sequence on your property.
How much does a commercial or HOA gate installation cost in Roseville?
Commercial and HOA gate installations typically start at $7,000 to $9,500 for a fully automated access system and go up from there depending on gate width, DoorKing access controls and operator capacity. Call (855) 431-0356 to schedule an on-site estimate for the property.
Do I need a permit for a gate installation in Roseville?
Gates and the electrical work tied to an automated operator often require a permit in Roseville, and the fee varies by project size. Call the City of Roseville building department to confirm what your installation needs. For installation work or gate repair in Roseville, call (855) 431-0356 for a free estimate.
If your gate has stopped working reliably, the repair or replacement decisions come first. Visit our Roseville service page to see how we handle both sides of that call, from a stuck hinge to a failed electric drive board. If you’re ready to price a new gate, see our guide to gate installation in Roseville, and for automated systems review our electric gate repair service in Roseville. We also cover swing gate work in swing gate repair for Roseville and slide gate problems in sliding gate repair for Roseville. Homeowners in nearby communities can reach us through Rocklin, Citrus Heights, Lincoln and Granite Bay, and we also cover Folsom and Auburn. HOA and commercial property managers can see brand-specific guidance in our LiftMaster gate opener troubleshooting guide and our DoorKing gate opener troubleshooting guide.
Contact Us for a Free Gate Installation Estimate in Roseville
If you’re weighing a gate project in Roseville, the fastest way to a real number is to have us look at the property. We’ll walk the site, talk through material and operator options, and hand you a written estimate at no cost. We work on equipment from LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule, and our technicians have up to 15 years of experience. Whether the job is a manual gate, a full automated driveway system, or a repair on a gate you already own, it’s all part of the same trade and the same call. All pricing is per job, set by the written estimate.
Call (855) 431-0356. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Gate Repair Roseville.
Pricing reflects the Roseville market as of 2026. Gate Repair Roseville offers free estimates – call (855) 431-0356.
What Our Customers Say
"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Javier Martinez"Hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a whole new gate, which two other companies had pushed for."
- Claudia Reyes"Solar panel on our remote gate wasn't keeping the battery up through the winter. He repositioned it, replaced the battery, and explained the math on why the old placement was never going to work."
- Kevin Sutton